Effects of different oil additives on water resistance of corn starch straws.

To investigate the effect of oil additives on improving the water resistance of corn starch straws, corn oil (CO), soybean oil (SO), rapeseed oil (RO), peanut oil (PO), lard (LD) and coconut oil (CCO) were chosen and compared the structure and properties of starch straws with different oil additives. Corn starch straws (CS), and starch straws supplemented with CO, SO, RO, PO, LD and CCO were prepared by thermoplastic extrusion. The results showed that the incorporation of oils effectively enhanced the water resistance of starch straws such as water absorption, water solubility and water swelling performance. Meanwhile, the flexural strength of starch straws significantly increased. There was no significant linear relationship among starch chain length, oil unsaturation and straw performance. Among seven starch straws, S-SO had the strongest hydrogen bond interaction (3289 cm-1) and relaxation time (0.96 ms). The S-CO had the highest relative crystallinity (16.82 %) and degree of double helix (1.535), hence resulting in the lowest water absorption and solubility values, the highest flexural strength (23.43 MPa), the highest ΔT value (9.93 °C) and ΔH value (4.79 J/g). S-RO had the highest thermal transition temperatures.

Physicochemical properties and in vitro digestibility of ginseng starches under citric acid-autoclaving treatment.

In this study, the effects of citric acid-autoclaving (CA-A) treatment on physicochemical and digestive properties of the native ginseng starches were investigated. The results showed that ginseng starch exhibited a B-type crystal structure with a low onset pasting temperature of 44.23 ± 0.80 °C, but high peak viscosity and setback viscosity of 5897.34 ± 53.72 cP and 692.00 ± 32.36 cP, respectively. The granular morphology, crystal and short-range ordered structure of ginseng starches were destroyed after CA-A treatment. The more short-chain starches were produced, resulting in the ginseng starches solubility increased. In addition, autoclaving, citric acid (CA) and CA-A treatment promoted polymerization and recrystallization of starch molecules, increased the proportion of amylopectin B1, and B3 chains, and improved molecular weight and resistant starch (RS) content of ginseng starches. The most significant multi-scale structural change was induced by CA-A treatment, which reduced the relative crystallinity of ginseng starch from 28.26 ± 0.24 % to 2.75 ± 0.08 %, and increased the content of RS to 54.30 ± 0.14 %. These findings provided a better understanding of the structure and properties of Chinese ginseng starches and offered new ideas for the deep processing of ginseng foods.

Effects of purple potato anthocyanins on the in vitro digestive properties of starches of different crystalline types.

This study explored the potential of purple potato anthocyanins (PPAs) in regulating the digestive properties of starches of various crystalline types. In vitro digestion experiments indicated that PPAs inhibit the hydrolysis of rice starch (A-type) better than that of garden pea starch (C-type) and potato starch (B-type). Further structural assessment of different PPA-starch systems showed that PPAs and starch likely interact through non-covalent bonds, resulting in structural changes. Microstructural changes observed in the starches were consistent with the in vitro digestion results, and the chain length and proportions of short/long chains in amylopectin molecules affected the binding strengths and interaction modes between PPAs and starch. Hence, the three starches differed in their PPA loading efficiency and digestibility. These discoveries contribute to a deeper understanding of the mechanisms underlying the inhibition of starch digestibility by PPAs. They can aid the formulation of value-added products and low-glycemic-index foods.

Potential relation between starch granule-associated proteins and retrogradation properties of buckwheat starch.

To elucidate the effect of starch granule-associated proteins (SGAPs) on retrogradation properties of buckwheat starch, the retrogradation properties of Tartary buckwheat starch (TBS) and common buckwheat starch (CBS) before and after removal of SGAPs were systematically investigated, with wheat starch (WS) as reference. A significant decrease in gel strength of starches and density of starch aggregates were observed after removing SGAPs. The results were in line with the changes in retrogradation enthalpy of starches and short-range ordered structure of starch aggregates. After removing SGAPs, the retrogradation enthalpy of TBS decreased from 4.16 J/g to 3.74 J/g, CBS decreased from 4.05 J/g to 3.35 J/g and WS decreased from 3.27 J/g to 2.81 J/g, respectively. Taken together the results of LF-NMR, FTIR and rheological analysis, it can be concluded that SGAPs could promote the hydrogen bond interactions between starch molecules by competitively binding with water molecules, enhancing the rearrangement of starch molecules and forming a more ordered structure. Overall, the study suggested that the presence of SGAPs could enhanced the interaction between starch molecules chains, thus accelerated the retrogradation process. The research results provide more information about SGAPs in buckwheat starch and support further study for manipulation of starch properties.

Multipurpose arrowroot starch films with anthocyanin-rich grape pomace extract: Color migration for food simulants and monitoring the freshness of fish meat.

Extraction of anthocyanins from grape pomace, is a way of valuing these abundant by-products with low added value. Its integration into films may allow it to be used in bioactive packaging, which creates new color and solubility properties for food and smart food packaging which tracks the freshness of fish. Films of arrowroot starch added with different concentrations of grape pomace extract (GPE) were flexible to handle, reddish and presented a high content of anthocyanins. The water vapor permeability increased by 17 %, while the tensile strength of arrowroot starch film decreased by 79 % with the addition of 40 % GPE. The addition of GPE increased the solubility of the starch film in aqueous and lipid food simulants by 121 and 119 %. The GPE pigment preferentially migrated to the aqueous simulant due to the hydrophilic nature of anthocyanins and starch. The GPE film showed distinguishable color changes in different pH buffer solutions from pink at pH 2 to light blue at pH 7 and slightly yellowish green at pH 10. When the composite films were monitored for fish meat freshness, the change in color of the film from reddish pink to slightly green after 96 h of storage at 25 °C was evident.

Interactions of hsian-tsao polysaccharide with corn starch to reduce its in vitro digestibility.

Hsian-tsao polysaccharide (HP) with preferable bioactivities was used to produce starchy gel foods. This study elucidated how interactions of HP (0-0.6 %, w/v) with gelatinized corn starch (CS, 6 %, w/v) reduced in vitro digestibility of CS. The CS digestibility (82.85 %, without HP) was reduced to 68.85 % (co-heated) and 74.75 % (non-co-heated) when 0.6 % HP was added, demonstrating that HP reduced the CS digestibility to a larger extent under co-heating by both HP-CS interactions and inhibiting digestive enzyme activities by HP which was dominated under non-co-heating. Moreover, when co-heated, HP bonded to the amylose of CS via physical forces with a composite index of 21.95 % (0.4 % HP), impeded CS swelling and promoted CS aggregation with the average particle size increased to 42.95 µm (0.6 % HP). Also, the HP-CS complexes formed strong association network structures that increased their apparent viscosity and digestive fluid viscosity. Additionally, HP enhanced the short-range ordered structure and crystal structure of CS. These results evidenced that HP-CS interactions significantly reduced the CS digestibility by forming physical barriers, viscosity effects, and ordered structures, to hinder the enzymes from accessing starch matrices. This laid a foundation for applying HP to starchy foods with a low predicted glycemic index.

Unveiling biological activities of biosynthesized starch/silver-selenium nanocomposite using Cladosporium cladosporioides CBS 174.62.

BACKGROUND AND OBJECTIVES: Microbial cells capability to tolerate the effect of various antimicrobial classes represent a major worldwide health concern. The flexible and multi-components nanocomposites have enhanced physicochemical characters with several improved properties. Thus, different biological activities of biosynthesized starch/silver-selenium nanocomposite (St/Ag-Se NC) were assessed. METHODOLOGY: The St/Ag-Se NC was biosynthesized using Cladosporium cladosporioides CBS 174.62 (C. cladosporioides) strain. The shape and average particle size were investigated using scanning electron microscope (SEM) and high-resolution transmission electron microscope (HR-TEM), respectively. On the other hand, the St/Ag-Se NC effect on two cancer cell lines and red blood cells (RBCs) was evaluated and its hydrogen peroxide (H2O2) scavenging effect was assessed. Moreover, its effects on various microbial species in both planktonic and biofilm growth forms were examined. RESULTS: The St/Ag-Se NC was successfully biosynthesized with oval and spherical shape and a mean particle diameter of 67.87 nm as confirmed by the HR-TEM analysis. St/Ag-Se NC showed promising anticancer activity toward human colorectal carcinoma (HCT-116) and human breast cancer (MCF-7) cell lines where IC50 were 21.37 and 19.98 µg/ml, respectively. Similarly, little effect on RBCs was observed with low nanocomposite concentration. As well, the highest nanocomposite H2O2 scavenging activity (42.84%) was recorded at a concentration of 2 mg/ml. Additionally, Staphylococcus epidermidis (S. epidermidis) ATCC 12,228 and Candida albicans (C. albicans) ATCC 10,231 were the highly affected bacterial and fungal strains with minimum inhibitory concentrations (MICs) of 18.75 and 50 µg/ml, respectively. Moreover, the noticeable effect of St/Ag-Se NC on microbial biofilm was concentration dependent. A high biofilm suppression percentage, 87.5% and 68.05%, were recorded with S. epidermidis and Staphylococcus aureus (S. aureus) when exposed to 1 mg/ml and 0.5 mg/ml, respectively. CONCLUSION: The biosynthesized St/Ag-Se NC showed excellent antioxidant activity, haemocompatibility, and anti-proliferative effect at low concentrations. Also, it exhibited promising antimicrobial and antibiofilm activities.

Investigation of physio-mechanical, antioxidant and antimicrobial properties of starch-zinc oxide nanoparticles active films reinforced with Ferula gummosa Boiss essential oil.

The production of surface compounds coated with active substances has gained significant attention in recent years. This study investigated the physical, mechanical, antioxidant, and antimicrobial properties of a composite made of starch and zinc oxide nanoparticles (ZnO NPs) containing various concentrations of Ferula gummosa essential oil (0.5%, 1%, and 1.5%). The addition of ZnO NPs improved the thickness, mechanical and microbial properties, and reduced the water vapor permeability of the starch active film. The addition of F. gummosa essential oil to the starch nanocomposite decreased the water vapor permeability from 6.25 to 5.63 g mm-2 d-1 kPa-1, but this decrease was significant only at the concentration of 1.5% of essential oils (p < 0.05). Adding 1.5% of F. gummosa essential oil to starch nanocomposite led to a decrease in Tensile Strength value, while an increase in Elongation at Break values was observed. The results of the antimicrobial activity of the nanocomposite revealed that the pure starch film did not show any lack of growth zone. The addition of ZnO NPs to the starch matrix resulted in antimicrobial activity on both studied bacteria (Staphylococcus aureus and Escherichia coli). The highest antimicrobial activity was observed in the starch/ZnO NPs film containing 1.5% essential oil with an inhibition zone of 340 mm2 on S. aureus. Antioxidant activity increased significantly with increasing concentration of F. gummosa essential oil (P < 0.05). The film containing 1.5% essential oil had the highest (50.5%) antioxidant activity. Coating also improved the chemical characteristics of fish fillet. In conclusion, the starch nanocomposite containing ZnO NPs and F. gummosa essential oil has the potential to be used in the aquatic packaging industry.

Effects of frying on the surface oil absorption of wheat, potato, and pea starches.

The effects of structural changes on surface oil absorption characteristics of wheat starch, pea starch and potato starch during frying under different water content (20%, 30%, 40%, 50%) were studied. Fried potato starch with a 40% water content exhibited the highest surface oil content. When the initial moisture content reached 30%, the scattering intensity of the crystal layer structure decreased for wheat and pea starches, while the scattering peak for potato starch completely disappeared. At 40% moisture content, the amorphous phase ratio values for fried potato, wheat and pea starches were 13.50%, 11.78% and 11.24%, respectively, and the nitrogen adsorption capacity of fried starch decreased in turn. These findings that the structure of potato starch was more susceptible to degradation compared to pea starch and wheat starch, resulting in higher surface oil absorbed by potato starch during frying process.

Potato starch/naringenin complexes for high-stability Pickering emulsions: Structure, properties, and emulsion stabilization mechanism.

In this study, potato starch (PS)/naringenin (NAR) complex was prepared, and its properties and emulsification behavior were evaluated. The experimental results demonstrated that NAR successfully formed a complex with PS molecules through hydrogen bonds and other non-covalent interactions. The emulsifying capacity (ROV) of PS/NAR complex with 16 % composite ratio was 0.9999, which was higher than PS (ROV = 0.3329) (p < 0.05). Based on particle property analysis and molecular dynamics simulation, the mechanism of improving the emulsification performance might be the action of the benzene ring of NAR and intermolecular hydrogen bonding. In addition, the stability of the Pickering emulsions with PS/NAR complexes as emulgators was significantly improved. The emulsifying and rheological behavior of starch-based Pickering emulsions could be adjusted by changing the proportion of the complexes. Results demonstrated that the PS/NAR complexes might be a prospective stabilizer of Pickering emulsions based on starch material and might expand the use of PS in edible products.

"Development and characterization of edible films based on starch isolated from different Colombian potato varieties".

This work reports on the extraction and characterization of the behavior of starch from residues of several potato varieties (Criolla, Sabanera and Pastusa) of Colombian origin from the Andean region using different techniques and the evaluation of the effect of citric acid (CA) on the grain morphology. Additionally, films were produced with each one of the extracted starches and glycerol. Pastusa variety starch shows a higher granule size than the other varieties and Pastusa starch shows lower amylose content compared to Sabanera and Criolla. Criolla and Pastusa starches exhibit more thermal stability than Sabanera starch. Starch-glycerol films were also produced using the cast solving method. The films were mechanically analyzed by tensile test and the barrier properties were assessed by water vapor permeability (WVP). The tensile strength of the films varied in the 2.0-2.4 MPa range, while the elongation at break was comprised between 25 and 32 %. With regard to water vapor permeability, the obtained values fall within the 4-7 × 10-10 g m-1 s-1 Pa-1 range. It was observed that the thickness of the films and the protein content affected water vapor permeability, increasing this value at higher levels of thickness.

The multi-scale structures and in vitro digestibility of starches with different crystalline types induced by dielectric barrier discharge plasma.

The effects of plasma treatment on multi-scale structures and in vitro digestibility of starches isolated from Tartary buckwheat (TBS), potato (PTS), and pea (PS), were investigated. The results from SEM and CLSM showed that plasma treatment resulted in the extension of pores from the starch hilum to the surface. The XRD and 13C CP/MAS NMR spectra demonstrated that the crystalline type of three starches was not changed by plasma treatment, while the RC and double helix content of TBS increased. Besides, the single helix content and the proportion of amorphous phase decreased following the treatment, which was consistent with the result of SAXS. However, the PTS and PS showed the opposite results by plasma treatment. In addition, the modification significantly changed the molecular weight (Mw) and chain length distribution of all the starches, among which the Mw of PTS fell drastically from 2.45 × 107 g/mol to 1.74 × 107 g/mol. The in vitro digestibility of starches increased significantly when treated with plasma, in which TBS exhibited the biggest increase for its inside-out and side-by-side digestion manners. Therefore, plasma treatment led to different alteration trends for multi-scale structures with quite various change extent for in vitro digestibility about different crystalline starches.

Enhancing bread preservation through non-contact application of starch-based composite film infused with clove essential oil nanoemulsion.

In this study, we have successfully produced a corn starch-based composite film through the casting method, formulated with clove essential oil nanoemulsion (NCEO) and corn starch. The physical and chemical changes of the composite films were investigated at various concentrations (10 %, 20 % and 40 %) of NCEO. Furthermore, the non-contact preservation effects of the composite films on bread during 15-day storage were also examined in this study. As the concentration of NCEO increased, the composite films presented a gradual thinning, roughening, and yellowing in appearance. Following this, the water content, water vapor permeability rate, and elongation at break of the films decreased, while their hydrophobicity, tensile strength, antioxidant and antimicrobial activity increased accordingly. Through FT-IR, X-ray diffraction and thermal gravimetric analysis, it was demonstrated that NCEO has strong compatibility with corn starch. Additionally, the indices' analysis indicated that utilizing the composite film incorporating 40 % NCEO can significantly boost the shelf life and quality of bread. Moreover, it was revealed that application of the non-contact treatment with composite film could potentially contribute certain preservation effects towards bread. In light of these findings, the composite film with non-contact treatment exhibits potential as an effective, safe, and sustainable preservation technique for grain products.

Impact of cyclic and continuous dry heat modification on the structural, thermal, technological, and in vitro digestibility properties of potato starch (Solanum tuberosum L.): A comparative study.

Dry heat treatment (DHT) has been demonstrated as a viable method for starch modification, offering benefits due to its environmentally friendly process and low operational costs. This research modified potato starch using different DHT conditions (continuous-CDHT and cyclic-RDHT), with durations ranging from 3 to 15 h and 1 to 5 cycles, at 120 °C. The study investigated and compared the structural, thermal, pasting, and morphological properties of the treated samples to those of untreated potato starch, including in vitro digestibility post-modification. DHT altered the amylose content of the biopolymer. X-ray diffraction patterns transitioned from type B to type C, and a decrease in relative crystallinity (RC%) was observed. Morphological changes were more pronounced in starches modified by RDHT. Paste viscosities of both CDHT and RDHT-treated starches decreased significantly, by 61.7 % and 58.1 % respectively, compared to native starch. The gelatinization enthalpy of RDHT-treated starches reduced notably, from 17.60 to 16.10 J g-1. Additionally, starch digestibility was impacted, with cyclic treatments yielding a significant increase in resistant starch content, notably an 18.26 % rise. These findings underscore the efficacy of dry heat in enhancing the functional properties of potato starch.

Effect of hydrocolloids on starch digestion: A review.

Rapidly digestible starch can increase postprandial blood sugar rapidly, which can be overcome by hydrocolloids. The paper aims to review the effect of hydrocolloids on starch digestion. Hydrocolloids used to reduce starch digestibility are mostly polysaccharides like xanthan gum, pectin, ß-glucan, and konjac glucomannan. Their effectiveness is related to their source and structure, mixing mode of hydrocolloid/starch, physical treatment, and starch processing. The mechanisms of hydrocolloid action include increased system viscosity, inhibition of enzymatic activity, and reduced starch accessibility to enzymes. Reduced starch accessibility to enzymes involves physical barrier and structural orderliness. In the future, physical treatments and intensity used for stabilizing hydrocolloid/starch complex, risks associated with different doses of hydrocolloids, and the development of related clinical trials should be focused on. Besides, investigating the effect of hydrocolloids on starch should be conducted in the context of practical commercial applications rather than limited to the laboratory level.

Incorporating edible oil during cooking tailors the microstructure and quality features of brown rice following heat moisture treatment.

While brown rice (BR) has numerous nutritional properties, the consumption potential of which is seriously restricted since the poor cooking quality and undesirable flavor. Here, edible oils (pork lard and corn oil, 1-5 wt%) were incorporated during the cooking of BR following heat moisture treatment. Incorporating corn oil rather than lard significantly ameliorated the texture properties (e.g. hardness, cohesiveness, and chewiness) and sensory properties of cooked BR. Both lard- and corn oil-incorporated cooked BR showed obvious structural changes accompanied by the formation of amylose-lipid complexes during cooking. It was confirmed that the incorporation of lard and corn oil allowed a higher degree of short-range molecular order, more V-type starch crystallites, and elevated nano-structural arrangements. Additionally, a decreased hardness (from 559.04 g to 424.18 g and 385.91 g, respectively) and enriched resistant starch (RS) were also observed, the highest RS content (15.95 % and 16.32 %, respectively) was observed when 1 wt% of lard and corn oil were incorporated.

Improving the Three-Dimensional Printability of Potato Starch Loaded onto Food Ink.

This study focuses on improving the 3D printability of pea protein with the help of food inks designed for jet-type 3D printers. Initially, the food ink base was formulated using nanocellulose-alginate with a gradient of native potato starch and its 3D printability was evaluated. The 3D-printed structures using only candidates for the food ink base formulated with or without potato starch exhibited dimensional accuracy exceeding 95% on both the X and Y axes. However, the accuracy of stacking on the Z-axis was significantly affected by the ink composition. Food ink with 1% potato starch closely matched the CAD design, with an accuracy of approximately 99% on the Z-axis. Potato starch enhanced the stacking of 3D-printed structures by improving the electrostatic repulsion, viscoelasticity, and thixotropic behavior of the food ink base. The 3D printability of pea protein was evaluated using the selected food ink base, showing a 46% improvement in dimensional accuracy on the Z-axis compared to the control group printed with a food ink base lacking potato starch. These findings suggest that starch can serve as an additive support for high-resolution 3D jet-type printing of food ink material.

Rheological properties and microstructure of wheat flour dough systems with enzyme-hydrolyzed mashed potatoes.

The interest in incorporating potatoes into wheat dough is increasing. However, potatoes exhibit significant viscosity during thermal processing, affecting product processing and quality. This study aims to find an effective method to reduce the viscosity of mashed potatoes. We aimed to compare the effects of different enzymes (α-amylase, ß-amylase, and flavourzyme) and concentrations (0.01%, 0.05%, and 0.1%) on the micromorphology and rheological properties of mashed potatoes and potato-wheat dough. The impact of flavourzyme was the most significant (p<0.05). When enzyme concentration increased, viscosity decreased, and the degree of structural damage, indicated by increased porosity. Notably, the addition of flavourzyme can increase the content of sweet and umami free amino acids, improving the flavor of mashed potatoes. The scanning electron microscopy and confocal laser scanning microscopy images of potato-wheat dough revealed that enzyme-hydrolyzed mashed potatoes had improved homogeneity, reestablished the dough continuity, and strengthened the three-dimensional structure comprising proteins and starch. Notably, flavourzyme demonstrated the most significant effect on enhancing the protein-starch network structure. This was attributed to the exposure of functional groups resulting from protein hydrolysis, facilitating interaction with starch molecules. Our findings indicate that the addition of 0.1% flavourzyme (500 LAPU/g, pH 5.5, 55 ± 2°C, 30 min treated) was the most effective in reducing viscosity and reconstructing the gluten network. Enzymatic hydrolysis plays a vital role in the production of high-quality potato products, with particular importance in the baking industry, where flavourzyme exhibits significant potential. PRACTICAL APPLICATION: Enzymatic hydrolysis plays a vital role in the production of high-quality potato products, with particular importance in the baking industry, where flavourzyme exhibits significant potential.

Structure and functional characteristics of starch from different hulled oats cultivated in China.

This work aimed to evaluate the structure and functional characteristics of starch from ten hulled oat cultivars grown in different locations in China. The protein, phosphorus, amylose, and starch contents were 0.2-0.4 %, 475.7-691.8 ppm, 16.2-23.0 %, and 93.6-96.7 %, respectively. All the starches showed irregular polygonal shapes and A-type crystallization with molecular weights ranging from 7.2 × 107 to 4.5 × 108 g/mol. The amounts of amylopectin A (DP 6-12), B1 (DP 13-24), B2 (DP 25-36), and B3 (DP > 36) chains were in the ranges of 10.3-16.0 %, 54.5-64.8 %, 16.5-21.1 %, and 4.9-13.1 %, respectively. The starches differed significantly in gelatinization temperatures, pasting viscosity, solubility, swelling power, rheological properties, and digestion parameters. The results revealed that the larger particle size could increase the peak viscosity of the starch paste. The presence of phosphorus increased the gelatinization temperature and enhanced the resistant starch content. The starch granules with higher crystallinity contained a higher proportion of phosphate, which increased final viscosity and setback viscosity but decreased rapidly digestible starch. Overall, oat starch with a high phosphorus content could be used to prepare low-glycemic-index food for diabetes patients.

Novel and safe debranched starch-zinc complexes with endoconcave structure as zinc supplements.

Zinc deficiency is a serious risk to human health and growth, especially in children. The development of zinc supplements can effectively reduce this harm. Here, a series of debranched starch­zinc complexes (DS-Zn) were prepared, whose zinc complexation was inversely proportional to the amylopectin content in the debranched starch (DS). The physicochemical properties of DS-Zn were characterized using the conductivity, XRD, iodine staining and thermogravimetry. Combined with XPS, solid-state 13C NMR and IR, it was elucidated that the structure of DS-Zn is endoconcave structure with 2-O and 3-O of DS on the inner side and 6-O of DS on the outer side, where zinc is located. The DS-Zn exhibits good biosafety including blood, cellular and mutagenicity. In vitro simulations of digestion and zinc-deficient cellular models showed that DS-Zn was more tolerant to the gastrointestinal environment and more effective in zinc supplementation (increased by 33 %) than inorganic zinc supplements. Utilizing the compressibility of starch, DS-Zn was prepared as a more palatable oral cartoon tablet for children. This study will provide important support to advance the development and application of novel starch-based zinc nutritional supplements.